|address: East of yangjia villiage,huashan sub-district,licheng district,jinan city
| Home > After Service
|1.DSP controller dies
Change a new DSP controller power supply (+5v) in the control box
Use the UPS
2. The machine doesn’t go home.
Restart the DSP controller
Use a new DSP controller
Recover the data in DSP controller: MENU=>SYSTEM MAINTENACE=>DATA SETUP=>RECOVER DATA
Reinstall the DSP program ZHBUSB: copy from the CD we sent with the machine.
3. Machine moves to the opposite direction
The cable maybe loose and you can check the cable.
Change the wire port A+ and A- on motor driver: you can find A+ and A-on the driver in the control box.
Change a new red limit switch
Change the cable connected with the limit switch
4. Computer dies when downloading file
Data is inordinate and format the data in DSP controller: MENU=>SYSTEM MAINTENANCE=>DATA SETUP=>FORMAT DATA
Enlarge the EMS memory and CPU
Change a better computer
5.Main spindle doesn’t rotate
Voltage is too low and use the UPS
Check the cable connected with the main spindle
Change a new transducer
Change a new main spindle
Date out of order after being copied and recover the data: MENU=>SYSTEM MAINTENACE=>DATA SETUP=>RECOVER DATA
6. Machine doesn’t work accurately
Change the motor of every axis or change the motor driver.
Use ground wire
Fasten the linker of the screw ball
7. Engraving size is not right
Change the pulse equivalent according to the type of the machine (screw machine: 320 160 320; gear machine: 127.3 127.3 400; 320,320,320 for XHYZ6090): MENU=>SYSTEM MAINTENACE=>SYSTEM PARAMATERS=>PULSE EQUIVALENT.
8. Machine doesn’t work after opened (including the machine don’t go home)
The switch is broken, change a new switch
There is something wrong with the power, check or change the power
Check the cable connected with the switch and pin in one side of the cable
9. Machine strikes sideward peg when it is working
The sensor switch is broken or the sheet copper of the sensor switch is distort, change a new sensor switch or fix the sheet copper
The dimension of the machine in controller is not correct, reset the dimension according to the working size (the soft limited in the DSP): MANU=>MANUAL SETUP=>MOTION LIMIT.
10. Blade is broken when engraving
Lower the engraving speed: MANU=>MANUAL SETUP=>MOTION PARAMATERS LOW SPEED/HGIH SPEED.
If the material is too thick, engrave by steps
Change a better quality blade
Collet is in a wrong position and correct it.
11. There are some leftover of the material when the machine is working.
Rectify the interspace of the screw of every axis in DSP: MENU=>SYSTEM MAINTENACE=>SCREW INTERSPACE
Change the bearing on the screw ball
Fasten the linker of Y axis (for ball screw machine)
12. Red sensor switch is ok but can’t stop the machine
Sensor switch is dirty and clean it
Sheet copper is too far away from the red sensor switch, the best distance is 1-2mm
When we operate machine manually, the sensor switch doesn’t work
13 Add machine in soft ware TYPE3
Open TYPE3, and find the machining=> set up machines =>choose the FAUNC OMD in CNC machines=>ok
14 X-axis or y-axis doesn’t move
Usually it is the problem of the stepper motor, driver and cable connected with the x-axis or y-axis, check them and correct
15 How to protect the vacuum hold down table
Don’t hollow out the material when engraving
16 How to change Chinese version to English (DSP)
Open English version ZHBUSB, Download Controller Menu and Download Label.
17.How to solve the problem of message over Z + limited in Type3
We need to set up machine When use s TYPE3, the initial position and end position of Z-axis are the same and higher than Z axis between contour.
18. How to change the language of TYPE3 from Chinese to English
Open the soft ware type3 and press the button F10. It will appear option windows. You can choose English.
19. Oil of the vacuum pump used in CNC router XHYC1325
Use engine oil 68#